KITCHEN GADGETS

Should You Buy Expensive Brass Fittings?

An alloy of zinc and copper, brass fittings has been known for its strength and durability. These over sixty different kinds of brasses have specific uses for high machining, cold working, casting, electrical, architectural, fluid handling, decorative application, and so on.  Just like other materials, it has alternative in the form of stainless steel fitting, which of course, in cheaper price.

When these inexpensive stainless steel fitting can do the same job, should you still buy the expensive brass fittings?  Definitely, the answer is yes.

Basically, brass fittings have the best quality in its various uses. Its alternative might do the same job but there would be a great difference in the effectiveness of these materials. Brass fittings have better quality because of its composition, zinc and copper that made it sturdy. So, over the years, brass fittings can assure of the same efficiency in its application.

Worrying on the performance of the brass alternatives is a trouble. For several times, you need to check it out to avoid some accidents caused by its malfunction. Hence, with brass fittings, you can comfortably settle down concerning its efficiency. These are usually used in lift truck sections, railway carriages, gas valves, and gears for cars. 

Comparing the price of stainless steel fittings and brass fittings, the latter may be more expensive, yet, it would last for many years. On the other hand, stainless steel fittings, as made from recycled materials of nickel, might let you change the fittings for several times, especially is subjected to extreme temperatures. Simply stated, the cheaper alternative would be more expensive because the cost can be multiply for several times, as you need to change the fittings over and over again.

When handling fluid, the perfectly fabricated brass fittings along with a Teflon tape certainly provide a protected, leak-proof seal. More so, brass can effectively join two materials such as pipes than any other alternative, without worrying on its sturdiness especially if subjected to pressures. These are usually used by oil companies because it does not cracked easily.

Brass fittings, with a little amount of Tin, became highly non-corrosive materials. It is resistant to rust, so, it is highly recommended as materials for seawater and acidic environment. Meaning to say, this high-tensile material can be used in almost anywhere.

With its physical appearance, the golden surfaces of brass fittings make it more attractive and appealing when it comes to architectural and decorative application. It can easily match and improve the interior designs, providing an elegant atmosphere. Even jewelers use brass because it never tarnished.

If you want to make the most from your money, brass fittings are the best choice than its alternative products. The quality of brass fittings is proven to be cheaper in the long time because of its various properties. You can never go wrong with brass because of its précised specification that assures you will never do any re-work for a long time. The comfort and peace of mind it gives you can never be measured and incomparable than its alternative.

About the Author

Know more about beverage tubing at InstallationPartsSupply.com.

#9 Unibit Drill Bit 2 Hole Sizes $61.99 OHZ1720: Features: -Drill bit.-Ideal for drilling holes into thin material such as stainless steel, copper, brass, aluminum, plastic and laminates.-Single flute cutting edge for greater control through steps.-Patented single flute cutting edge gives a true round hole every time.-3 flattened shank prevents slipping in drill chuck.-Speed Point tip penetrates faster and prevents walking.-7/8” and 1-1/8”.-#9.-Carded.

(1) WHITE 4INCH COTTON BUFF,(1) BUFFING COMPOUND 4PK,(1) TAPERED SPINDLE $23.94 Cotton Buff: 50 ply with leather center & 4 rows of concentric stitching. The faces are pre-raked for even acceptance of any type of compound. Engineered, balanced and trued for dependable long term wear. Primarily used for a final finishing buff to produce a desired finish. Buffing Compound Kit Contains 1 each 1inch x 2 ?inch Tubes: Black Emery Compound: Used for coarse buffing, removes burrs, rust, scratches, iron steel and other hard metals. Red Jewelers Rouge: Creates high luster on soft metals, brass, copper, gold and all precious metals. Gray Stainless Compound: Used for stainless steel, nickel plate and plastics. Brown Tripoli: Removes surface imperfections on all base metals brass, aluminum and pewter. Tapered Spindle: Threaded end designed to screw into leather or lacquered-center buffs.

(1) WHITE 6INCH COTTON BUFF,(1) BUFFING COMPOUND 4PK,(1) TAPERED SPINDLE $27.05 Cotton Buff: 50 ply with leather center & 4 rows of concentric stitching. The faces are pre-raked for even acceptance of any type of compound. Engineered, balanced and trued for dependable long term wear. Primarily used for a final finishing buff to produce a desired finish. Buffing Compound Kit Contains 1 each 1inch x 2 ?inch Tubes: Black Emery Compound: Used for coarse buffing, removes burrs, rust, scratches, iron steel and other hard metals. Red Jewelers Rouge: Creates high luster on soft metals, brass, copper, gold and all precious metals. Gray Stainless Compound: Used for stainless steel, nickel plate and plastics. Brown Tripoli: Removes surface imperfections on all base metals brass, aluminum and pewter. Tapered Spindle: Threaded end designed to screw into leather or lacquered-center buffs.

(1) YELLOW 4INCH COTTON BUFF,(1) BUFFING COMPOUND 4PK,(1) TAPERED SPINDLE $24.94 Cotton Buff: 50 ply with leather center & 4 rows of concentric stitching. The faces are pre-raked for even acceptance of any type of compound. Engineered, balanced and trued for dependable long term wear. Primarily used in the initial buffing process to deburr and remove scratches. This buff is a more aggressive cutting buff. Buffing Compound Kit Contains 1 each 1inch x 2 ?inch Tubes: Black Emery Compound: Used for coarse buffing, removes burrs, rust, scratches, iron steel and other hard metals Red Jewelers Rouge: Creates high luster on soft metals, brass, copper, gold and all precious metals. Gray Stainless Compound: Used for stainless steel, nickel plate and plastics. Brown Tripoli: Removes surface imperfections on all base metals brass, aluminum and pewter. Tapered Spindle: Threaded end designed to screw into leather or lacquered-center buffs.

(1) YELLOW 6INCH COTTON BUFF,(1) BUFFING COMPOUND 4PK,(1) TAPERED SPINDLE $28.97 Cotton Buff: 50 ply with leather center & 4 rows of concentric stitching. The faces are pre-raked for even acceptance of any type of compound. Engineered, balanced and trued for dependable long term wear. Primarily used in the initial buffing process to deburr and remove scratches. This buff is a more aggressive cutting buff. Buffing Compound Kit Contains 1 each 1inch x 2 ?inch Tubes: Black Emery Compound: Used for coarse buffing, removes burrs, rust, scratches, iron steel and other hard metals. Red Jewelers Rouge: Creates high luster on soft metals, brass, copper, gold and all precious metals. Gray Stainless Compound: Used for stainless steel, nickel plate and plastics. Brown Tripoli: Removes surface imperfections on all base metals brass, aluminum and pewter. Tapered Spindle: Threaded end designed to screw into leather or lacquered-center buffs.

0.75 Brass Fitting Kit for Water Filters $9.43 CUX1039: Features: -Brass fitting kit.-Fits 0.5” and 0.75” pipes. Includes: -Includes compression fittings for 0.75” copper pipe, adapters for 0.5” copper pipe and teflon tape. Dimensions: -Overall dimensions: 6” H x 4” W x 1.25” D.

05 Series Two Handle Tub Faucet $116 PPR1781: Features: -Brass lever handles.-Meets ADA requirements.-For wall-mount installation.-8” body.-8” fixed cast brass valve body.-1/2” union inlets x 1/2” IP outlets.-With copper union adapters.-Ceramic disc valve. Includes: -Configured for two handles, included. Color/Finish: -Polished chrome finish. Dimensions: -Overall Dimensions: 10.38” H x 8” W x 5” D. Collection: -Part of the Savannah Collection.

07 SeriesTwo-Handle Shower with Valve Option – Finish: Polished Chrome with White Porcelain $106.72 Shown in Polished Brass – PPR1941: Features: -Two-lever handles.-Two-handle configuration.-Ceramic disc valves.-” union inlets x ” I.P. outlets, with copper union adapters.. Includes: -Includes bell shower head, arm, flange and handles. Construction: -Solid brass construction. Color/Finish: -Polished brass finish.-Unfinished. Specifications: -Requires 07-31XA valve. Dimensions: -Overall Dimensions: 10.38” H x 8” W x 5” D.-Overall Dimensions: 10.56” H x 8” W x 5” D. Collection: -Part of the Savannah Collection.

1 x 12 FatMax Cold Chisel With Bi-Material Hand Guard 16-3 $11.83 OPY1532: Features: -Used for cutting and shaping wrought iron, cast iron, steel, brass, bronze, copper, aluminum, bolts, nuts and rivets.-1” cutting edge.-Carded. Dimensions: -12” length.

1-3/4IN BI-METAL HOLE SAW $9.77 Power Change hole saw system has a quick change arbor that quickly removes holesaws from mandrel, easy plug removal and cuts material up to 1-5/8 deep. Used in applications such as cutting in aluminum, brass, bronze, copper, plastic, stainless steel, wood, and other compositions.

1.0 gpf/ 3.8 Lpf Royal Optima G2 Plus Battery Powered Flush Valve for Urinal $340.1 SLN1086: Features: -1.0 gpf/3.8 Lpf Low consumption.-PERMEX Synthetic Rubber Diaphragm with Dual Filtered Fixed Bypass.-Flex Tube Diaphragm designed for improved life and reduced maintenance.-ADA Compliant OPTIMA Plus Battery Powered Infrared Sensor for automatic ”No Hands” operation.-Infrared Sensor with Multiple-focused, Lobular Sensing Fields for high and low target detection.-Latching Solenoid Operator.-User friendly three (3) second Flush Delay.-Courtesy Flush Override Button.-Four (4) Size AA Batteries factory installed.-”Low Battery” Flashing LED.-Infrared Sensor Range Adjustment Screw.-Initial Set-up Range Indicator Light (first 10 minutes).-Chrome Plated Metal Handle Cap.-0.75” I.P.S. Screwdriver Bak-Chek Angle Stop.-Free Spinning, Vandal Resistant Stop Cap.-Adjustable Tailpiece.-High Back Pressure Vacuum Breaker Flush Connection with One-piece Bottom Hex Coupling Nut.-Spud Coupling and Flange for 0.75” Top Spud.-Sweat Solder Adapter with Cover Tube and Cast Set Screw Wall Flange.-High Copper, Low Zinc Brass Castings for Dezincification Resistance.-Fixed Metering Bypass and No External Volume Adjustment to Ensure Water Conservation.-Flush Accuracy Controlled by CID Technology.-Diaphragm, Stop Seat and Vacuum Breaker to be molded from PERMEX Rubber Compound for Chloramine resistance. Construction: -Engineered Metal Cover with replaceable Lens Window. Dimensions: -11.5” Height (to center of inlet).

1.0gpf/3.8 Lpf Royal Urinal Flush Valve $125.33 SLN1001: Features: -PERMEX Synthetic rubber diaphragm with dual filtered fixed bypass.-ADA Compliant metal oscillating non-hold-open handle with triple seal handle packing.-Non-Hold-Open integral solenoid operator, fixed metering bypass and no external volume adjustment to ensure water conservation.-Free spinning vandal resistant stop cap.-High back pressure vacuum breaker flush connection and spud coupling with one-piece bottom hex coupling nut.-Sweat solder adapter with cover tube and cast set screw wall flange.-High copper, low zinc brass castings for dezincification resistance.-Flush accuracy controlled by CID technology.-Adjustable tailpiece.-Diaphragm, handle packing, stop seat and vacuum breaker to be molded from PERMEX rubber compound for chloramine resistance.-Spud coupling and flange for 0.75” top spud.-0.75” I.P.S. Screwdriver Bak-Chek angle stop. Dimensions: -11.5” Height (to center inlet).

1.25 Round Cabinet Knob – Finish: Black $3 QMI1000: Features: -Round knob.-Easy to install. Options: -Available in polished brass, polished chrome, satin brass, satin nickel, antique brass, Italian bronze, oil rubbed bronze, tumbled antique brass, tumbled copper, tumbled pewter, black and white finishes. Construction: -Zinc construction. Dimensions: -Overall dimensions: 1” H x 1.25” W x 1.25” D. Warranty: -Limited lifetime warranty.

1.25 Round Cabinet Knob – Finish: Polished Chrome $3 QMI1000: Features: -Round knob.-Easy to install. Options: -Available in polished brass, polished chrome, satin brass, satin nickel, antique brass, Italian bronze, oil rubbed bronze, tumbled antique brass, tumbled copper, tumbled pewter, black and white finishes. Construction: -Zinc construction. Dimensions: -Overall dimensions: 1” H x 1.25” W x 1.25” D. Warranty: -Limited lifetime warranty.

1.25 Round Cabinet Knob – Finish: Tumbled Pewter $3 QMI1000: Features: -Round knob.-Easy to install. Options: -Available in polished brass, polished chrome, satin brass, satin nickel, antique brass, Italian bronze, oil rubbed bronze, tumbled antique brass, tumbled copper, tumbled pewter, black and white finishes. Construction: -Zinc construction. Dimensions: -Overall dimensions: 1” H x 1.25” W x 1.25” D. Warranty: -Limited lifetime warranty.

1.5 Drain with Overflow, Cover, and Grid Strainer – Finish: Brushed Nickel $20.15 DNZ1902: Features: -For use with lavatory bowls without overflow.-Clamshell package. Includes: -Includes decorative cover for lavatory sinks with overflow. Options: -Available in the following finishes: chrome, antique copper, brushed nickel, polished brass, and oil rub bronze. Dimensions: -Overall dimensions: 8.5” H x 2.6” W. Warranty: -Danze products are covered by a manufacturer’s limited ”lifetime” warranty on finish, leaks and manufacturing defects.

1.5 Drain with Overflow, Cover, and Grid Strainer – Finish: Chrome $13.16 DNZ1902: Features: -For use with lavatory bowls without overflow.-Clamshell package. Includes: -Includes decorative cover for lavatory sinks with overflow. Options: -Available in the following finishes: chrome, antique copper, brushed nickel, polished brass, and oil rub bronze. Dimensions: -Overall dimensions: 8.5” H x 2.6” W. Warranty: -Danze products are covered by a manufacturer’s limited ”lifetime” warranty on finish, leaks and manufacturing defects.

1.5 Drain with Overflow, Cover, and Grid Strainer – Finish: Oil Rub Bronze $17.52 DNZ1902: Features: -For use with lavatory bowls without overflow.-Clamshell package. Includes: -Includes decorative cover for lavatory sinks with overflow. Options: -Available in the following finishes: chrome, antique copper, brushed nickel, polished brass, and oil rub bronze. Dimensions: -Overall dimensions: 8.5” H x 2.6” W. Warranty: -Danze products are covered by a manufacturer’s limited ”lifetime” warranty on finish, leaks and manufacturing defects.

1.5 Drain with Overflow, Cover, and Grid Strainer – Finish: Polished Brass $20.15 DNZ1902: Features: -For use with lavatory bowls without overflow.-Clamshell package. Includes: -Includes decorative cover for lavatory sinks with overflow. Options: -Available in the following finishes: chrome, antique copper, brushed nickel, polished brass, and oil rub bronze. Dimensions: -Overall dimensions: 8.5” H x 2.6” W. Warranty: -Danze products are covered by a manufacturer’s limited ”lifetime” warranty on finish, leaks and manufacturing defects.

1.5 GPM Indoor Electric Tankless Water Heater $187.98 RHE1011: Features: -Indoor electric tankless water heater.-On unit temperature control.-LEDs indicate active element and standby mode.-Rugged brass and copper heat exchanger.-Modulating power.-Energy star. Dimensions: -Standard 0.5” water connection.-Overall dimensions: 10.25” H x 5.37” W x 5.37” D. Warranty: -Manufacturer provides ten years limited heat exchanger warranty.-Manufacturer provides one year parts warranty.

1.5 gpf/ 5.7 Lpf Royal Optima G2 Plus Battery Powered Flush Valve for Urinal $374.73 SLN1087: Features: -1.5 gpf/5.7 Lpf Low consumption.-PERMEX Synthetic Rubber Diaphragm with Dual Filtered Fixed Bypass.-Flex Tube Diaphragm designed for improved life and reduced maintenance.-ADA Compliant OPTIMA Plus Battery Powered Infrared Sensor for automatic ”No Hands” operation.-Infrared Sensor with Multiple-focused, Lobular Sensing Fields for high and low target detection.-Latching Solenoid Operator.-User friendly three (3) second Flush Delay.-Courtesy Flush Override Button.-Four (4) Size AA Batteries factory installed.-”Low Battery” Flashing LED.-Infrared Sensor Range Adjustment Screw.-Initial Set-up Range Indicator Light (first 10 minutes).-Chrome Plated Metal Handle Cap.-0.75” I.P.S. Screwdriver Bak-Chek Angle Stop.-Free Spinning, Vandal Resistant Stop Cap.-Adjustable Tailpiece.-High Back Pressure Vacuum Breaker Flush Connection with One-piece Bottom Hex Coupling Nut.-Spud Coupling and Flange for 0.75” Top Spud.-Sweat Solder Adapter with Cover Tube and Cast Set Screw Wall Flange.-High Copper, Low Zinc Brass Castings for Dezincification Resistance.-Fixed Metering Bypass and No External Volume Adjustment to Ensure Water Conservation.-Flush Accuracy Controlled by CID Technology.-Diaphragm, Stop Seat and Vacuum Breaker to be molded from PERMEX Rubber Compound for Chloramine resistance. Construction: -Engineered Metal Cover with replaceable Lens Window. Dimensions: -11.5” Height (to center of inlet).

1.6 gpf/ 6.0 Lpf Optima G2 Plus Battery Powered Flush Valve $362.59 SLN1085: Features: -1.6 gpf/6 Lpf Low consumption.-PERMEX Synthetic Rubber Diaphragm with Dual Filtered Fixed Bypass.-Flex Tube Diaphragm designed for improved life and reduced maintenance.-ADA Compliant OPTIMA Plus Battery Powered Infrared Sensor for automatic ”No Hands” operation.-Infrared Sensor with Multiple-focused, Lobular Sensing Fields for high and low target detection.-Latching Solenoid Operator.-User friendly three (3) second Flush Delay.-Courtesy Flush Override Button.-Four (4) Size AA Batteries factory installed.-”Low Battery” Flashing LED.-Infrared Sensor Range Adjustment Screw.-Initial Set-up Range Indicator Light (first 10 minutes).-Chrome Plated Metal Handle Cap.-1” I.P.S. Screwdriver Bak-Chek Angle Stop.-Free Spinning, Vandal Resistant Stop Cap.-Adjustable Tailpiece.-High Back Pressure Vacuum Breaker Flush Connection with One-piece Bottom Hex Coupling Nut.-Spud Coupling and Flange for 1 1/2” Top Spud.-Sweat Solder Adapter with Cover Tube and Cast Set Screw Wall Flange.-High Copper, Low Zinc Brass Castings for Dezincification Resistance.-Fixed Metering Bypass and No External Volume Adjustment to Ensure Water Conservation.-Flush Accuracy Controlled by CID Technology.-Diaphragm, Stop Seat and Vacuum Breaker to be molded from PERMEX Rubber Compound for Chloramine resistance. Construction: -Engineered Metal Cover with replaceable Lens Window. Dimensions: -11.5” height (to center inlet).

1/2 CPPR COMPR X 3/4 HSE CON $11.92 Features heavy pattern rough brass, stuffing box design, and coated tee handle. 1/2 copper compression x 3/4 hose connection.

1/2 Cp Rb Coupling $9.78 ANDERSON METAL CP RB COUPLING For corrosive environment Used with brass, copper and iron pipe Low to medium pressure lines Crome plated threaded. 1/2 size. ANDERSON METAL CP RB COUPLING For corrosive environment Used with brass, copper and iron pipe Low to medium pressure lines Crome plated threaded.

1/2 F.I.P. x 1/2 Sharkbite Brass Elbow $7.58 Easy, quick push-fit connection of water distribution pipe. Design certified and listed to ASSE 1061/NSF 61. Listed by IAPMO and certified for potable and hydronic heating water distribution. Certified for underground applications and as a manufactured joint without access panels. Meet UPC, IPC, and CUPC requirements. Fits outside diameter controlled copper, CPVC, or PEX pipe . Body composed of solid DZR brass. 1/2 x 1/2 FNPT

1/2 FITTING BRUSH CARDED $3.63 Easy to use, contoured, heavy duty handle is perfect for cleaning copper and brass fittings. High carbon twisted steel shaft and brush gives long life and durability.

1/2 M.I.P. x 1/2 Sharkbite Brass Elbow $7.27 Easy, quick push-fit connection of water distribution pipe. Design certified and listed to ASSE 1061/NSF 61. Listed by IAPMO and certified for potable and hydronic heating water distribution. Certified for underground applications and as a manufactured joint without access panels. Meet UPC, IPC, and CUPC requirements. Fits outside diameter controlled copper, CPVC, or PEX pipe . Body composed of solid DZR brass. 1/2 x 1/2 MNPT

1/2 WIRE HANDLE FITTING BRUSH $3.36 ID fitting brush with wire handle for cleaning copper and brass fittings. High carbon steel brush ensures a long lasting, durable and sharp cutting surface.

1/2 X .3 Cp Nipple $10.17 ANDERSON METAL BRASS PIPE NIPPLE 1/2 x 3 . Chrome Plated Pipe Nipple. Pipe fitting used to connect brass, copper & iron pipe. Fainr vibration resistance. ANDERSON METAL BRASS PIPE NIPPLE 1/2 x 3 . Chrome Plated Pipe Nipple. Pipe fitting used to connect brass, copper & iron pipe. Fainr vibration resistance .

1/2PEX10 1/4 TURN FF VALVE $26.62 1/2 Male. Easy quarter turn operation. IAPMO – ANSI/NSF-61 approved. Maximum 125 PSI working pressure. Chrome plated brass ball. Teflon seats. 60% copper alloy brass construction. 3/4 hose thread outlet. Large flow rate. Rust resistant handle. Pipe threads comply with ANSI B1.20.1. Hose threads comply with ANSI B1.20.7. Solder ends comply with ANSI-16.18. Handy carton.

1/2PEX12 1/4 TURN FF VALVE $27.54 1/2 Male. Easy quarter turn operation. IAPMO – ANSI/NSF-61 approved. Maximum 125 PSI working pressure. Chrome plated brass ball. Teflon seats. 60% copper alloy brass construction. 3/4 hose thread outlet. Large flow rate. Rust resistant handle. Pipe threads comply with ANSI B1.20.1. Hose threads comply with ANSI B1.20.7. Solder ends comply with ANSI-16.18. Handy carton.

1/2PEX14 1/4 TURN FF VALVE $27.92 1/2 Male. Easy quarter turn operation. IAPMO – ANSI/NSF-61 approved. Maximum 125 PSI working pressure. Chrome plated brass ball. Teflon seats. 60% copper alloy brass construction. 3/4 hose thread outlet. Large flow rate. Rust resistant handle. Pipe threads comply with ANSI B1.20.1. Hose threads comply with ANSI B1.20.7. Solder ends comply with ANSI-16.18. Handy carton.

1/2PEX8 1/4 TURN FF VALVE $25.51 1/2 Male. Easy quarter turn operation. IAPMO – ANSI/NSF-61 approved. Maximum 125 PSI working pressure. Chrome plated brass ball. Teflon seats. 60% copper alloy brass construction. 3/4 hose thread outlet. Large flow rate. Rust resistant handle. Pipe threads comply with ANSI B1.20.1. Hose threads comply with ANSI B1.20.7. Solder ends comply with ANSI-16.18. Handy carton.

1/2ipsx4 Nipple $6.95 PLUMB PAK PIPE NIPPLE Used with brass, copper and iron pipes . Low to medium pressure lines. Yellow brass . Carded. Finishing with brass polised. 1/2 i.p.s. x 4 .. PLUMB PAK PIPE NIPPLE Used with brass, copper and iron pipes . Low to medium pressure lines. Yellow brass . Carded

1/2pex4 1/4 Turn Ff Valve $22.67 SILLCOCKS TURN OF VALVE 1/2PE x 4 1/4 TURN FF VALVE 3/4 hose thread outlet Chrome plated brass ball Rust resistant handle Easy quarter turn operation Maximum 125 PSI working pressure Teflon seats 60 percent copper alloy brass construction Large flow rate. 1/2PE x 4 1/4 TURN FF VALVE 3/4 hose thread outlet Chrome plated brass ball Easy quarter turn operationMaximum 125 Large flow rate

1/4 COPPER DISP IMB LO LED $19.44 1/4 turn brass ball valve, copper sweat, nails preloaded, right or left hand installation, no support bracket needed, valve complies with requirements of NSF 61, Section 9. Box: 3.2 W x 4.15 H x 2.35 D. Faceplate: 5 W x 5.89 H x .5 D. Boxed.

1/4in X Mip Dishwasher Elbow $7.6 1/4×3/8m shark d/w elbow. Brass Male dishwasher elbow. Push-fit fitting connects copper, CPVC, and PEX pipe in any combination. Use no soldering or glue. Certified to 200 P.S.I. and 200 F. Certified for potable water and hydronics. Easy-to-disconnect if

1/4×7/8 Elb Ballcck Toilet Cnt $8.14 1/4×7/8bc toilet elbow. Chrome-plated brass toilet valve elbow. Connects copper, CPVC, and PEX pipe in any combination. Certified to 200 P.S.I. and 200 F. Certified for potable water and hydronics. Easy-to-disconnect if needed. Listed to ASSE 1061/NSF 6

1/8 To 1-1/8 Tubing Cutter $10.06 STANLEY TUBE CUTTER Stanley brand (licensing agreement) 1/8-1-1/8 OD (3mm-30mm) Cuts copper, brass & aluminum tubing Carded Discovery CON, NBR, SUP, HWU. Stanley brand (licensing agreement) 1/8-1-1/8 OD (3mm-30mm) Cuts copper, brass & aluminum tubing

1/8 To 1-1/8 Tubing Cutter $18.43 Capacity 1/8 to 1-1/8 . Cuts tubing of hard or soft aluminum, brass, copper and thin wall conduit. Enclosed feed mechanism to protect threads against dirt and damage. Tubing rides freely on hardened rollers. Cuts cleanly without burrs or tubing distortion. Special Superior long-life alloy cutter wheels. Retractable, hardened reamer blade built in, locks open or closed. PROFESSIONAL QUALITY

10 Cut Off Wheels Sprue Cutting Blade Tools for Dremel $5.99 Ten (10) pc 1 1/2 Cut Off Wheels for Dremel This set contains 10 pieces of metal cutter blades The cutting discs are excellent to cut thin metal sheet, brass/copper/zinc pipes, etc The cutting discs center holes are 1/4 The cutting discs diameters are 1 1/4 The cutting discs are made from top quality rubber bonded aluminum material NOTE: Pictures are for illustration purpose only, actual item may slightly vary in appearance and design

10.24 Kitchen Sink Faucet – Finish: Old Bronze $594 Shown in Chrome – EEK1329: Features: -Kitchen sink faucet. -Available in Old Bronze, Chrome, Gold, Old Copper or Brushed Nickel finishes. -Solid brass construction. -Single hole. -14 Two flexible tubes. -360 Degree swivel spout. -Overall dimensions: 10.24 H x 7.28 D. For more information on this product please view the Sheet(s) below: Specifications Sheet

100FT RG6 COAX CABLE BLACK $25.51 Designed to optimize performance from digital sources such as HDTV. 75 ohm, corrosion resistant brass F compression connectors. 24 Karat gold electroplated connectors and dielectric material insulation for optimum signal transfer. Durable 18 AWG copper coated steel center conductor. Aluminum braided shield prevents signal loss, aluminum foil shield minimizes interference. Heavy duty outer jacket for long life protection. RG6 quad shield cable transfers signals 3 times faster and prevents signal loss up to8 times better than standard RG6 cable.

10IN FROST FREE HYDRANT $28.07 Notched flange permits easy anchoring to frame buildings. Constructed of all brass and type L copper, except packing handle. Green epoxy-coated handle.

11.2 Acanthus Medallion in White $214.2 Pictured in antique brass – ELL3106: Features: -Ceiling medallion. Color/Finish: -Antique brass finish.-Chrome finish.-Copper finish.-Gold finish.-White finish. Dimensions: -Overall dimensions: 1” H x 11.2” W. Collection: -Acanthus collection.

11/32x5in Multi-Purp Drill Bit $7.24 For rotary and percussion drilling. Chrome vanadium steel shaft and shank provides extra hardness and enormous strength. Special negative back grinding enables tip to bore through steel, wood, tile, marble, porcelain, glass, concrete, plastic and cast iron with a filing action rather than a cutting action. No center punch required, eliminates walking. Cobalt and Tungsten carbide tip for max hardness and resistance to heat and wear. High tech bonding allows bit to withstand drilling temperatures up to 1,900 degrees Fahrenheit. Easy to resharpen. For cordless drills, corded drills and drill presses. NOTE: Not recommended for use on mild steel. This includes aluminum, angle iron, copper, galvanized pipe, brass and stainless steel. COBALT & TUNGSTEN CARBIDE TIP MULTI-PURPOSE Carded Dia. x Lgth. Ins.=11/32 x 5

1100 Series Single Handle Tub and Shower Faucet – Finish: Oil Rubbed Bronze $193.99 Shown in Oil Rubbed Bronze – PGS1430: Features: -Solid brass & copper waterways.-ADA Compliant.-Quarter turn waterless cartridge.-Ergonomic handle rotation for easy On/Off.-Flexible connections simplify installation.-Matching bathroom accessories available.-Oil Rubbed Bronze.-Brushed Nickel. Dimensions: -Overall Dimensions: 7.08” H x 9.25” W x 11.42” D. Collection: -Series 1100 Collection.

12 Abrasive Wheel w/Arbors Gunsmith for Dremel Tool $10.99 12Pcs Rotary Abrasive polishing wheels, (WHEEL COLOR MAY VARY) This set contains 12 tool bits for your Dremel machine Ideal for removing rust, corrosion from, any metal surface (e.g. brass, copper, etc.) Also for removing paint off wood or metal Wheel diameter is approximately 15/16 The shank size is 1/8 This is perfect for jewelers, metalsmiths, gunsmiths, locksmiths, and other professions Maximum operating speed 15,000/min NOTE: Pictures are for illustration purpose only, actual item may slightly vary in appearance and design

12 Ceiling Fan Downrod – Finish: Amber Bronze $20 Pictured in Brushed Nickel – CFC1207: Features: -Ceiling fan downrod.-Patented Hang-Thru hands free installation. Options: -Available in bright brass, antique brass, matte black, classic white, snow white, glossy black, navajo white, weathered copper, brushed nickel, rustic iron, washed bronze, bronze patina, amber bronze, graphite, architectural white, oil-rubbed bronze, aged gold, vintage pewter, mandarin red, travertine, dark bamboo, textured matte black, mocha, dark walnut, sea grass, or antique pewter finish. Dimensions: -Perma-lock locks fan permanently into place for easy installationOverall dimensions: 12” H.

12 Ceiling Fan Downrod – Finish: Antique Brass $13 Pictured in Brushed Nickel – CFC1207: Features: -Ceiling fan downrod.-Patented Hang-Thru hands free installation. Options: -Available in bright brass, antique brass, matte black, classic white, snow white, glossy black, navajo white, weathered copper, brushed nickel, rustic iron, washed bronze, bronze patina, amber bronze, graphite, architectural white, oil-rubbed bronze, aged gold, vintage pewter, mandarin red, travertine, dark bamboo, textured matte black, mocha, dark walnut, sea grass, or antique pewter finish. Dimensions: -Perma-lock locks fan permanently into place for easy installationOverall dimensions: 12” H.

Tags: copper brass difference, copper brass mailbox, copper brass prices, copper brass sales, copper brass sales california